کدهای خطای HP DesignJet 1055CM

آبان 26, 1395

Code	Description
0000D8	External Library Error.
010020	Firmware DIMM Test failure.
010021	Memory DRAM DIMM Test failure.
010023	EEROM Test failure.
01002D	The Main PCA cannot communicate with the Carriage.
010040	Error in Paper-axis Encoder quadrature.
010041	Error in Scan-axis Encoder quadrature.
010042	Error in Service Station-axis Encoder quadrature.
010050	PostScript Processing Error.
01009X	Error in Paper-axis Motor Encoder
02xxxx	PostScript/Firmware Error.
048xxx	The EIO card is from a third party vendor and may not be fully compliant with the IIO Protocol specification 2.0 OR the EIO Card firmware is not updated.
04Cxxx	EIO Accessories (EIO Card/Hard Disk Drive) Error.
060301	One of the Printheads has an Internal Electrical Problem.
060305	Thermal Shutdown error (one of the Printheads has gone above the maximum Temperature). 00000000 - Cyan Printhead Failed. 00000001 - Magenta Printhead Failed. 00000002 - Yellow Printhead Failed. 00000003 - Black Printhead Failed.
060309	Problem with setting the Voltage of the Printheads.
06030A	Error in finding the Mark Encoder.
06030B	The Ambient Temperature measured is out of the normal range.
070100	Firmware Error.

Code	Description
080001	PostScript Error.
09xxxx	EIO Accessories (EIO Card/Hard Disk Drive) Error.
0A0000	The Air Pressure is below the minimum requirement.
0A0010	Problem in Pressurizing the Air System.
0A0020	Error in Calibrating the APS Sensor.
0A0030	Problem in Depressurizing Air System.
0A0040	Ink Tubes Initialization Failure Due to Low Air Pressure.
0A0050	The Printer has detected a leak in the Tubes System before the life of the System.
0A0060	The Printer has detected a leak in the Tubes System after the life of the System.
0A0070	The Backup EEROM contents stored in the Tubes System are not consistent with the ones required by the firmware.
0B0000	Bad Ambient Temperature measured.
0B0001	Bad Humidity read.
0B0002	Bad IDS pressure read.
0B0003	ADC0 Internal channels check Failure.
0B0004	Unable to detect Pump.
0B0005	Unable to detect Valve.
0B0006	The Trailing Cable has been incorrectly connected OR the fuse in the Electronics Module has been burned.
0B0007	Unable to detect Vacuum Fan.
0B0008	Unable to detect Cooling Fan.

Code	Description
0B0009	Unable to detect Aerosol Fan (Included on the Right Cover).
0B000A	Primer Shutdown Error.
0B000B	Pump or Pressure Sensor not working.
0B000C	Serial Device ADC test failure
0B000D	24 V source test failure.
0C0030	Bad Drop Detector.
0C0032	Drop Detector not Calibrated for all Printheads.
0C1000	Primer not Calibrated.
0C1001	Primer Shutdown Error.

نام و نام خانوادگی *	لطفا نام و نام خانوادگی خود را وارد نمایید.
پست الکترونیکی *	لطفا آدرس پست الکترونیکی خود را صحیح وارد نمایید.
موضوع پیام *	لطفا موضوع پیام ارسالی خود را بنویسید.
پیام *	لطفا متن پیام خود را تکمیل نمایید.
کد امنیتی *	کد امنیتی را صحیح وارد نمایید