کدهای خطای HP DesignJet 2000CP

آبان 26, 1395

Code	Description
0000D8	Library Error.
010020	The Checksum read on the Flash SIMM is incorrect.
010021	The baseDRAM or theRAM SIMM tests failed.
010022	The SWATH RAM test failed.
010023	A fuse on the Main PCA has blown.
010024	Problem initializingthe encoder pulse generator.
010030	One of the two interconnect boards not detected.
010031	The Printhead Primitive Driver ASIC Test Failed.
010032	Fan Test Failed -Current not detected in one or bothfans. Error data (XX): 1 -Electronics Module fan not running. 2 -Service station fan not running. 3 -Bothfans not running. 10 -Electronics Module fan is short-circuited. 20 -Service Station fan is short-circuited. 30 -Bothfans are short-circuited. 12 -Service Station fan is not running and the Electronics Module fan is short-circuited. 21 -Electronics Module fan is not running and the Service Station fan is short-circuited.
010033	The DC Motor Driver ASIC Test Failed.
010034	One of the DC Motors has failed. Error data: 00010000 -Y-axis Motor Failed. 00020000 -X-axis Motor Failed. 00030000 -Both DC Motors Failed.
010035	One of the Stepper Motors has failed. Error data (oXABCDEF): If the value of each letter is o, then the component is OK. If the value of each letter is different from 0 then the component has failed. X -Electronics signal failed (ignore other values). A -Elevator Stepper Motor Failed. B -Refill Stepper Motor Failed. C -Primer Stepper Motor Failed. D -Service station (Z-axis) Stepper Motor Failed. E -Service station (X-axis) Stepper Motor Failed. F -Bail Stepper Motor Failed.
010036	ADC Test Failure in the Main PCA A short circuit in the Y/X-axis or ANY stepper motor. This short circuit is causing some of the fuses in the Electronics Module to burn. Error data: 00000800 -Problem with the Y-axis. 00001000 -Problem with the X-axis.
010037	ADC Test Failure in the Carriage PCA.
010038	A Printhead voltage could not be set -Main PCA Failure.
010039	A Printhead voltage could not be set -Carriage PCA Failure
010040	The Ambient Temperature measured is out of the normal range.
010042	The status of one of the opticalsensors is not stable when it should be. Error data (X): 0 -Problem with the Media Sensor. 1 -Problem with the Pinch-arm Sensor. 2 -Problem with the Refill Assembly Sensor. 3 -Problem with the Elevator Sensor. 4 -Problem with the Service Station Sensor. 5 -Problem with the Primer Sensor.
010043	Problem with theCarriageBoard.

Code	Description
010100	Error reading the EEROM.
010101	An action outside the EEROM limits has been performed.
010102	Physical EEROM write and/or write operations failed. The EEROM data that is written does not match the data that is read.
010110	The content of the permanent configuration area of theEEROM is not valid when theprinter is initialized in Service Mode.
010111	The content of the User configuration area of the EEROM is not valid when the printer is initialized.
010120	The content of the permanent configuration area of the EEROM is not valid when the printer is initialized in Normal Mode.
010121	One of the banks of the user area was corrupted while writing or reading in that area.
020000	Error in finding the Primer home position.
020001	Error in finding the Elevator home position.
020002	Error in finding the Refill Arm home position.
020003	Error in finding the Refill Stepper Motor home position.
020004	Error in finding the Service Station home position.
020005	Elevator has problem reaching a desired position.
020006	The refill position in the Y-axis is not calibrated.
020010	Problem with fine movement of the Y-axis motor.
020011	Error during initialization of the Y-axis.
040601	The MIO card does not support the MIO 6 protocol. Cards with version 5 or below can not be used with this plotter. Version 5.1 cards behave as expected but do not support PML instructions. Install the latest version.
040xxx	MIO Card Error
050000	The Line Sensor has problems finding the Mark Encoder.

Code	Description
060000	The Line Sensor is not functioning properly because there is too much ambient light.
060100	Incorrect Line Sensor type in the EEROM.
060200	Incompatible Firmware and Carriage PCA.
060300	Incompatible Firmware and Line Sensor.
060400	Incompatible Carriage PCA and Line Sensor OR Line Sensor not calibrated after replacing Carriage Assembly.
060500	Line Sensor not calibrated.
07xxxx	Firmware Error.
080001	Hard Disk Drive installed without PostScript.
08xxxx	PostScript Error.
090004	PostScript installed without the Hard Disk Drive.
09xxxx	Hard Disk Drive Error.

نام و نام خانوادگی *	لطفا نام و نام خانوادگی خود را وارد نمایید.
پست الکترونیکی *	لطفا آدرس پست الکترونیکی خود را صحیح وارد نمایید.
موضوع پیام *	لطفا موضوع پیام ارسالی خود را بنویسید.
پیام *	لطفا متن پیام خود را تکمیل نمایید.
کد امنیتی *	کد امنیتی را صحیح وارد نمایید

کدهای خطای HP DesignJet 2000CP

فروشگاه

آدرس دفتر مرکزی